Build Cedar Planter Box

For the larger one, i cut 4 23s at 22 and the 16 planks at 22, as well. I used 1x6 cedar decking.

Building planter boxes Backyard planters, Building

This looks complex, but can be easily done on the miter saw or table saw.

Build cedar planter box. Bryan nelson this planter box will really show off the potted plants on your patio. For the smaller box, i cut 4 23 fence posts at 16 and 12 16 planks at 16. Cut a square out of each corner so that the cloth will fit around the legs on the inside.

For this step, i used the same technique as i did with the farmhouse center piece. These will become the sides of the planter box. Have you heard of a snapfence before?

Fold over each edge of the hardware cloth approximately 1. This cedar planter box is stunningly modern, unique, and more practical than you would even think. For a printable copy of the materials and instructions, scroll down.

Build a cedar planter box with construction lumber! Fold each side of the hardware cloth up to create a sort of basket to fit inside the planter. How to make a diy cedar planter box.

This planter is made completely out of cedar 1x12s. After i recovered from sticker shock, i made a beeline over to the cedar fence pickets to pick up 8 pickets at $2.55 a piece. Then, use a drill and galvanized screws to attach the ends of the.

This cedar planter box is just what i needed! You will lay 4 of the cedar fence post picket pieces on the two 2 by 2 pieces. Each box was under $10 and you can easily customize the size!

Once all of the wood has been cut, its time to build the cedar planter boxes. To build a wooden planter box, start by cutting some wooden planks so you have 2 that are 2 feet long and 2 that are 4 feet long. Now, add pocket holes to the 24s where you will attach the wood pieces together.

Cedar doesnt rot as quickly as fir wood, but fir resists warping and splitting over time better than cedar. Lay the 16.5 inch 24s on a flat surface, in groups of four. How to build a cedar planter box.

Center the casters and screw in place. Mitre the corners and dry fit. Then, use that dimension (ours was 14) and add 4 to it.

So i start the nails before i line the pieces up together. Start by measuring your plastic planter box. I just used some 1 finishing nails and wood glue to build the cedar planter boxes.

Now thaaaaats more like it, thank you very much. Before screwing down the swivel casters, rotate them to make sure they move freely and dont contact the edge of the cedar. Flip the box right side up, and fit the trim on the top.

Make sure ot lay them on a plat surface. To build your panels, follow the steps below. Purchase supplies and create a workspace in an area that will remain dry.

While the pickets are thinner than the traditional lumber that you would normally use to build planter boxes, they are sturdy and much less expensive. It not only looks great, but its sturdy enough to last a. I dont have a nailer.

First, lay out two of your 2 by 2 boards cut to 21 1/2 inches. Set your chop saw to cut at 8.5 degrees. This planter box consists of four separate panels and the bottom slats.

These are the corners of your cedar planter box. Apply 2 coats of penofin to cedar planks. I cut enough fence material to build 2 boxes.

Make sure the stationary casters face the same direction. Planter box made with cedar fence pickets during my internet search, i came across different plans that called for cedar fence pickets instead of cedar lumber. The cost to build two of these babies was about $20!

This is the dimension youll use for the long side of your top round of boards. To assemble the short side panels, attach three slats and two rails to each other using 1 screws from the inside.

diy planter box plans How To Make Wooden Planter Boxes